Whirlpool Duet dryers are been delivering their services for some years. They have a few different variants. They work similarly with a slight upgrade or downgrades.
To be very honest the units left there from this lineup are not too new or in very good condition.
Being older devices, they often get caught by different problems and beeping is the indication that your whirlpool duet dryer is not working properly or it has stopped working completely or partially.
We will be explaining why your Whirlpool Duet Dryer Beeps once and won’t start. The whole essay will be in random order, so make sure you don’t miss any part.
Whirlpool Duet Dryer Beeps Once Won’t Start [Reason and Explanation]
Primarily your Whirlpool Dryer may make two types of beep and tones. Though those don’t match in all the devices, first check the device manual properly. Firstly,
End Beep
Your dryer uses this beep to indicate that the drying cycle is completed.
For some models, you can even customize the beep behavior of the ending cycle. You may turn it off too.
Damp Beep
This is also a customizable beep module. Whatever this beep happens when the loads in the chamber are dump, not completely dry.
You may take the clothes out and dry them properly.
After these two, comes some casual issues that take place on the dryers. As,
Low Battery
Whirlpool dryer may make sounds like birds chirping after every few minutes. These beeps usually happen when the battery is low.
When the device has a low battery, the beeping will indicate it. Also, for excessive lower battery machines won’t start.
Control Panel Failure
This is predictable that your dryer is been working for years and maybe not be in a good condition. The control panel is a regularly used part of your dryer. So, there is a certain risk of it being damaged in the long run.
Even if you are a gentle user, still the control panel may get damaged in the long run. When the control panel is damaged, the sensor functions will be affected. As a result, for the wrong sensor command, the machine will keep beeping even if there is no legitimate reason for it.
Proper maintenance of the control panel may save you from this for longer. Also, if you are a victim, contact your nearest Whirlpool customer service for replacement or fixing.
As we are talking about Whirlpool Duet Dryer troubles, the certain thing we need to discuss is its error codes.
Well, because this is entirely related to the machine beeping. As we should know, beeping most often come from device errors and failures. Okay starting from,
PF (Power Failure)
A power failure is basically occurred from Outlet cords. It happens while the device is running.
Press the start button to continue or stop the cycle. But if you see the problem is continuing, then try checking the power cord. Maybe there is a hard bent or damage in the core. Which is making the power inconvenient and the device is failing in power supply and not starting.
So many of the users put the cables carelessly. The cords are kept on the hard bend for a longer time, even under the legs of heavy weighty things. This damages the cable and starts PF error as well as beep notifications.
F:01 (Main Electronic Board Failure)
Electronic board failure may come from different sources. Such as if the machine has gone through an extremely high voltage, it may spoil the connectors with heat and sparks. Sometimes continuous use and device heat may damage the circuit board.
Whatever in this kinda situation you can unplug the dryer for five minutes and then plug it in again. This may subtle the circuit and heat so that the device may run fine again.
But if the beep and error code remains the same better replace the main electronic control board.
F:22 (Outlet Thermistor Failure)
Sometimes the control panel detects that there is an open outlet Thermistor. For safety issues, you may hear your dryer beeping and shut down instantly.
Firstly, you have to know that, the thermistor is here the temperature sensor.
O troubleshoot the problem, make sure the device is switched off, and then check the resistance of the thermistor. The res should be about 10000 ohms.
In case there is a wrong resistance value and the thermistor is defective, you need to replace that.
Also the same troubleshoot for outlet failure error and beeps; Error code F:23
F:28 & F:29 (Moisture Sensor Failure)
Your dryer has to deal with a large number of wet things every time. So, that’s pretty normal if you find some vaporized water or clogged up the wet situation around cables, circuit boards, or wires.
But this moisture may create a short circuit and kill the device. So, as a safety feature, there are moisture sensors inside. In case there is moisture, the device will detect that and warn you with these 2 errors and beeps.
To fix it, unplug the dryer and check the connections of the wires properly. Clean the moisture and wait until it dries properly. Once it is dry switch the device back on.
Hopefully, the beep will be stopped and no error will be shown anymore.
Sometimes the device falls in trouble for left lint, fabrics, and similar objects. As your dryer has to deal with cloth and fabric objects for the whole time, that’s pretty simple if fabric or lint gets clogged up. In this situation the normal airflow gets restricted and the machine starts beeping with showing an F:30 Error.
Just cleaning the machine and removing those clogged-up objects will fix it instantly. But before you start cleaning, make sure you have turned the device off.
But out of the box, sometimes you may find that the machine is running completely well, there is no trouble. And the whole process, the cycle is functional.
Still, there is beeping continuously, and error codes are being shown even if no such error is happening.
This is maybe a situation of sensor malfunction. A quick reset may solve it.
Reset Your Whirlpool Duet Dryer
To reset your whirlpool duet dryer, simply unplug the device. Wait at least one minute and then turn it back on again. The reset is done and no error or wrong beep will be shown.
Won’t pull a long conversation, you got to know that, the basic reason for the whirlpool Duet Dryer beeping is End Beep and Damp Beep.
But other reasons like different error codes and hardware malfunctions also may happen. If you apply the processes we have shown properly, you will be able to fix them.
But in case the troubles are not going and the dryer keeps beeping continually, Call the nearest Whirlpool Service center and seek their service. Trying to repair from third-party organizations for saving money is not recommended. This may sometimes damage the device intentionally or unintentionally.
